The Journey of the Spore - The Built Environment Has an Error
BE-13

A spore a few thousandths of a millimetre across falls through still air at about half a millimetre per second, so the wind, not gravity, decides where it lands. Once it lands, the wall decides whether it grows: surface moisture, porosity, roughness and temperature govern colonisation, and established mould-growth models show why each wet winter advances growth that a dry summer only pauses. The practical conclusion is that how a building is cared for should follow mechanism, not appearance.
The Built Environment Has an Error
Stand on any British street after a wet winter and you will see it. One house has a clean face. The house next door, built the same year from the same brick, has a green band along the base of its north wall and black streaks under its sills. The owners do nothing differently. The difference is not housekeeping. It is physics and biology, and it starts with something too small to see.
This article follows one fungal spore from the moment it leaves its parent colony to the day it helps darken a whole street. Each stage is governed by an established law. Read together, they show that a building is not an inert surface waiting to get dirty. It is a habitat that is continually sampled, chosen and remodelled by living things.
One Piece of Housekeeping
Where this article gives numbers, they come from published research or standard physics, and the source is named. Where a mechanism is plausible but not yet measured on British walls, we say so. Worked examples are labelled as examples, not as measurements of a particular building.
Nothing here is a health claim. Damp and mould are associated with respiratory illness in published research, and that is why the law now regulates them, but we make no claim that our work treats or prevents any condition.
Liberation: The Spore Leaves Home
Many fungi launch their spores actively, but that launch is short-lived. A spore fired at a few metres per second loses its momentum to air resistance within a fraction of a millimetre. From then on, its fate is set by the balance between gravity and drag.
For a particle this small, that balance is described by Stokes' law. A spore a few thousandths of a millimetre across settles through still air at roughly half a millimetre per second. At that speed, the faintest updraft keeps it aloft for as long as the air keeps moving. It does not travel through the wind. It travels as part of it.
The Atmospheric Highway
Where a spore lands is a probability, not a point. Field measurements of airborne fungal spores show a dispersal pattern with a heavy tail: most spores settle close to their source, but a meaningful fraction is carried much further. Rieux and colleagues (2014) measured airborne ascospores travelling up to about a kilometre, while rain-splashed spores of the same organism stayed close to home.
That heavy tail is why mould seems to appear from nowhere. Most of the spores on your wall are local, from gardens, trees and neighbouring buildings, but some arrived on a weather front from another parish. Every façade on a street draws on the same shared supply.
Deposition: The Wall Chooses Its Colonists
On a vertical wall, gravity plays almost no part in the landing. Spores arrive by deposition from the moving air, governed by the thin, slow layer of air that clings to the surface. Sheltered, north-facing elevations, where that layer is calm and the surface stays damp, collect and keep more of what arrives.
Then the wall decides. The idea of bioreceptivity, introduced by Guillitte (1995), describes how readily a material is colonised, set by its porosity, roughness, mineral make-up and how long it stays wet. The single most important factor is water available at the surface. Two walls in the same rain can have opposite fates, decided by the material itself.
Germination: The Equation with a Memory
A spore can sit on a wall for months doing nothing. It germinates when the surface stays damp enough for long enough. For most mould on building materials, growth is possible only when the relative humidity at the surface is above roughly 80%, with the exact threshold depending on temperature and material.
The most widely used model for this is the VTT mould-growth model, developed by Hukka and Viitanen (1999) and refined since. It tracks a mould index from zero, a clean surface, to six, complete coverage. Two of its features explain a great deal. Below the critical humidity, growth stops. And when conditions turn dry, the index falls only slowly, much more slowly than it rose. Each wet winter pushes the index up; each dry summer merely pauses it. That is the mathematics behind the stain that comes back in the same place every year.
Surface Conquest: The Bloom After the Silent Years
In the early stages, fungal threads can be colourless and hard to see, spreading through the pores of the surface. A wall can look clean for years and then darken across a whole elevation in a single wet season. That is not the sudden arrival of new contamination. It is a long, hidden process becoming visible, often when the colony produces dark protective pigments such as melanin.
How fast a colony spreads across a wall is a question the mathematics of growth fronts can describe, but with care. Fungal growth by extension of thread tips advances as what mathematicians call a pushed front, and its speed cannot be read off a simple formula and used to calculate the underlying growth rates. The honest position is that spread is real and measurable, and that the simple textbook speed formula is a lower bound, not a prediction.
Penetration: Why a Clean-Looking Wall Is Not Always Clean
Water enters porous brick, stone and mortar by capillary suction. Its depth of penetration grows with the square root of time, the Lucas–Washburn relationship (Washburn, 1921). The first millimetres wet within minutes of rain; deeper penetration takes much longer. That idealised law over-predicts real walls once evaporation, gravity and irregular pores come into play, so it is best used as a scaling rule, not an exact depth.
Living organisms can also change how a surface wets. Fungi produce proteins called hydrophobins that alter the surface energy of pores, so a pore that has hosted growth can wet and dry differently from a clean one. Some growth also sits below the visible surface. That is why a quick surface wash can leave a wall looking clean while the conditions for regrowth remain.
The Moisture Loop Indoors
The same rules apply inside. Condensation forms wherever a surface falls below the dew point of the air touching it, calculated using the Magnus formula given in BS EN ISO 13788.
A worked example: on a cold night, with 2 °C outside and 21 °C inside at about 54% relative humidity, the indoor dew point is about 11.4 °C. An uninsulated ceiling-to-wall junction that falls to 9.1 °C is below that dew point and will collect condensation. Its temperature factor is about 0.37, well below the 0.75 that UK guidance on avoiding mould uses as a design minimum (BRE Information Paper 1/06). That corner will grow mould wet season after wet season unless the cold bridge or the moisture is dealt with.
Insulation can make this better or worse. A wall that cannot dry, because a layer stops vapour escaping, can trap moisture inside its structure. That is why transient hygrothermal assessment to BS EN 15026 matters whenever internal insulation is proposed on a solid wall.
Why Chemical Washing Does Not Last
Sodium hypochlorite washing bleaches and kills surface growth quickly, and the wall looks clean. But three things limit how long that lasts. Growth below the reach of the wash can survive. The wall's bioreceptivity, its porosity and roughness, is unchanged or can be made worse if the chemical attacks the binder or a water-repellent finish. And the shared supply of airborne spores never runs out.
There is a further nuance, and it matters. Visible growth is not automatic proof of damage. Research on biological films on stone, including work by Carter and Viles, shows that some growth can protect the surface beneath it. Jang and colleagues (2021) found, on British limestone, that mosses can shield the stone from light rain, and that removing them may disturb the moisture regime more than leaving them. The right intervention therefore depends on mechanism and material, not on appearance.
Materials: Why the Wall Decides
Fired clay brick has an open pore network that readily draws in water once its face is worn. Lime mortars and renders are vapour-open and forgiving, but they are soft and easily damaged by aggressive cleaning. Cement renders are less breathable and can trap moisture behind them. Polymer-modified and water-repellent renders depend on a surface finish that harsh cleaning can strip away.
Plastics are not immune either, but the details matter. Unplasticised PVC window frames contain no plasticiser and age mainly through sunlight. Plasticised PVC, used for flexible seals and gaskets, is different: Webb and colleagues (2000) showed that the fungus Aureobasidium pullulans colonised plasticised PVC within 25 to 40 weeks outdoors and could break down its plasticiser. That is why seals can harden and fail while the frame around them looks sound.
From One Wall to an Entire Road
Every mature colony becomes a source. Spores released from one wall rain onto its neighbours and travel further along the street. That is why whole terraces and estates darken together: they share one regional supply of spores, and the walls that stay wettest and are most receptive are the ones that show it first.
There is a public health dimension to the moisture behind this. A large review by Quansah and colleagues (2012) found that living with dampness was associated with roughly one-third higher odds of developing asthma, and the World Health Organization's 2009 guidelines on dampness and mould find sufficient evidence of an association with respiratory symptoms and asthma. That is why damp and mould in social housing are now regulated under Awaab's Law, with fixed deadlines for landlords. We assess the building, not the person: health questions belong to clinicians.
Adversarial Triangulation and Falsifiability
Three parts of this story are well established: how spores travel and land, how moisture and temperature control growth, and how water enters porous materials. One part is not yet settled, and we say so plainly: whether a thin biological film keeps a British brick or render wall wetter for longer after rain. It is plausible. It has not been measured on British walls.
That question can be tested. Paired cores, one colonised and one cleaned, taken from the same wall and dried side by side under controlled conditions, would show whether the biological layer changes drying. If the two dry at indistinguishable rates, the biological part of the argument is retired and we will say so. The test is described in our research programme, BE-14.
The Open Invitation
This article is one pillar of fifteen.
We invite surveyors, conservation officers and building scientists to test the chain set out here, and to tell us where the evidence says otherwise. We invite homeowners to look at their own street with new eyes: the wall that stays wet is the wall that grows.
Continue reading the series:
BE-04 Commercial Real Estate — The Yield Has a Substrate Footprint
BE-05 Construction Quality — The Snag Is a Substrate Chemistry Failure
BE-06 Procurement — The Lowest Bid Is a Probabilistic Liability
BE-08 Data & Digital Twins — The Twin Is Lying About the Wall
BE-09 Workforce — The Scholar-Technician Replaces the Commodity Trade
BE-10 Heritage Economics — The Listed Building Is a Yield Instrument
Wherever moisture, a mild temperature and time meet on a surface, biology follows. Caring for a building means reading that correctly, and intervening without destroying the fabric it runs on.
Read the industry discussion paper
Thank you for reading.
